Effects of feed composition,protein denaturation and storage of milk serum protein/lactose powders on lactosylation

During whey powder production, the feed is subjected to several heat treatments which can cause lactosylation of proteins. In this study, lactosylation of whey proteins was evaluated in spray-dried powders before and after storage by varying the native protein fraction as well as the serum protein/lactose ratio in the powders. The lactosylation of native α-lactalbumin and β-lactoglobulin in the powders before storage was not affected to a large extent by the protein denaturation or if the feed had been heat treated in a high or low lactose environment. After storage (relative humidity of 23.5%, 30 °C, 25 days), the kinetic of lactosylation tended to increase with increasing native protein fraction and bulk protein content in the powders. An explanation could be that proteins dissolved in the lactose glassy structure might have a lower reactivity, while proteins present in the protein glassy structure with dissolved lactose may display higher lactosylation reactivity.     

Granulation Tissue Enhanced with Aspirin and Omega-3 PUFAs as a Local Adjunct to the Surgical Treatment of Periodontitis

The topical application of aspirin and omega-3 polyunsaturated fatty acids (PUFAs) may trigger the resolution of inflammation by inducing the biosynthesis of pro-resolvers such as lipoxins and resolvins while also avoiding the side effects of systemic aspirin intake. This study assessed the effect of enhanced granulation tissue (EGT) on periodontal tissue regeneration through the local application of aspirin and omega-3 PUFAs directly to granulation tissue (GT) during periodontal surgery. This randomized controlled experiment assesses 38 pockets in 19 patients. In every patient, two similar intrabony periodontal defects are treated with an open flap debridement, one with EGT (GT extracted, enhanced with aspirin and omega-3 PUFAs, and replaced) and the other with standard GT removal. Clinical attachment level (CAL) and probing pocket depth (PPD) are assessed at baseline and 2 and 6 months after surgery. The experimental protocol (EGT) results in a greater CAL gain as compared to that in the controls at 6 months (p < 0.05), while PPD reduction is not affected. The retained GT does not compromise healing. EGT is proposed as a promising, inexpensive, and simple method that may improve the outcome of periodontal regenerative treatment. However, the described protocol requires optimization and further assessment. Practical Applications : The biosynthesis of mediators including resolvins and lipoxins triggered by aspirin and omega-3 PUFAs promote the resolution of inflammation, eventually leading to faster regeneration of inflamed tissues. While granulation tissue is a necessary component in wound healing, enhancing granulation tissue with aspirin and omega-3 PUFAs results in CAL gain in the surgical treatment of periodontal defects. Retained granulation tissue does not compromise periodontal healing. The EGT strategy is an inexpensive and simple method that may improve the clinical outcomes of regenerative periodontal procedures.     

Manufacturing catalyst-coated membranes by ultrasonic spray deposition for PEMFC: Identification of key parameters and their impact on PEMFC performance

This study deals with the manufacturing of catalyst-coated membranes (CCMs) for newcomers in the field of coating. Although there are many studies on electrode ink composition for improving the performance of proton-exchange membrane fuel cells (PEMFCs), there are few papers dealing with electrode coating itself. Usually, it is a know-how that often remains secret and constitutes the added value of scientific teams or the business of industrialists. In this paper, we identify and clarify the role of key parameters to improve coating quality and also to correlate coating quality with fuel cell performance via polarization curves and electrochemical active surface area measurements. We found that the coating configurations can affect the performance of lab-made CCMs in PEMFCs. After the repeatability of the performance obtained by our coating method has been proved, we show that: (i) edge effects, due to mask shadowing - cannot be neglected when the active surface area is low, (ii) a heterogeneous thickness electrode produces performance lower than a homogeneous thickness electrode, and (iii) the origin and storage of platinum on carbon powders are a very important source of variability in the obtained results.     

Spray pressure variation effect on the properties of CdS thin films for photodetector applications

Herein, we report the photosensing property of CdS thin films. CdS thin films were coated onto glass substrates via a spray pyrolysis method using different spray pressures. Prepared films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and optical and photoluminescence spectroscopy. XRD analysis demonstrated the growth of crystalline CdS films with crystallite sizes varying from 26 to 29 nm depending on the pressure. The SEM and EDAX analyses revealed nearly-stoichiometric CdS films with smooth surfaces and slight variation in grain morphology due to pressure changes. Optical measurements showed a direct bandgap varying from 2.37 eV to 2.42 eV due to pressure changes. A photodetector was also fabricated using the grown CdS films; the fabricated photodetector exhibited good performance depending on the spray pressure. A spray pressure of 1.5 GPa resulted in high photoresponsivity and external quantum efficiency.     

喷淋液滴在空气环境下的运动特性

本文以喷淋液滴在空气环境下运动特性为工程背景，建立单个液滴在常温、常压空气环境中的动量方程，分析液滴沉降特性、追赶特性及运动轨迹行为。计算结果表明，不同喷淋液滴初始条件下，短时间内存在重力大于曳力和重力小于曳力两种情况，但最终减速液滴均会达到受力平衡状态；液滴离开喷淋头后，垂向位移均迅速增大，液滴粒径越大、初始速度越大，垂向位移增长的速率也越大，达到相同位移的用时越短；液滴尺寸、初始速度相差越大，液滴追赶所用的时间越短，追赶位移越小，液滴尺寸、初始速度越接近，液滴追赶所用的时间越长，追赶位移越大；液滴初始速度越大、初始直径越大、喷射角度越大，横向速度消失越慢，达到的横向位移越大，喷射液滴覆盖的面积也越大。计算结果有助于优化工程实际中喷淋系统的设计与布置。     

内燃机活塞环表面处理技术

活塞环在内燃机中有着支撑、密闭、储油、导热的作用,内燃机活塞环制备材料应该具备优良的加工性能、耐高温、耐腐蚀、导热性好且具有良好的强韧性,较好的与气缸材料表面的磨合性能。球墨铸铁和专用钢材已经成为制备内燃机活塞环的基础材料,目前国内外采用多种表面处理技术比如:镀铬、氮化、PVD与CVD镀膜、喷钼、喷涂陶瓷层等表面处理工艺进行表面改性,提高内燃机活塞环的使用寿命和使用性能。需要不断研究和开发新的内燃机活塞环的表面处理技术来满足实际生产和应用中内燃机越来越高的要求。     

Twin screw granulation – review of current progress

Twin screw granulation (TSG) is a new process of interest to the pharmaceutical community that can continuously wet granulate powders, doing so at lower liquid concentrations and with better product consistency than found by a high shear batch mixer. A considerable body of research has evolved over the short time since this process was introduced but generally with little comparison of results. A certain degree of confidence has been developed through these studies related to how process variables and many attributes of machinery configuration will affect granulation but some major challenges still lay ahead related to scalability, variations in the processing regimes related to degree of channel fill and the impact of wetting and granulation of complex powder formulations. This review examines the current literature for wet granulation processes studied in twin screw extrusion machinery, summarizing the influences of operational and system parameters affecting granule properties as well as strives to provide some practical observations to newly interested users of the technique.     

Mechanical properties and microstructure of Yb2SiO5 environmental barrier coatings under isothermal heat treatment

Yb₂SiO₅ (ytterbium monosilicate) top coatings and Si bond coat layer were deposited by air plasma spray method as a protection layer on SiC substrates for environmental barrier coatings (EBCs) application. The Yb₂SiO₅-coated specimens were subjected to isothermal heat treatment at 1400 °C on air for 0, 1, 10, and 50 h. The Yb₂SiO₅ phase of the top coat layer reacted with Si from the bonding layer and O₂ from atmosphere formed to the Yb₂Si₂O₇ phase upon heat treatment at 1400 °C. The oxygen penetrated into the cracks to form SiO₂ phase of thermally grown oxide (TGO) in the bond coat and the interface of specimens during heat treatment. Horizontal cracks were also observed, due to a mismatch of the coefficient of thermal expansion (CTE) between the top coat and bond coat. The isothermal heat treatment improves the hardness and elastic modulus of Yb₂SiO₅ coatings; however, these properties in the Si bond coat were a little bit decreased.     

300M超高强钢在中性盐雾环境中的腐蚀行为及机制

摘要：为了研究300M超高强钢在中性盐雾环境中的腐蚀行为及腐蚀机制，采用失重法，宏观、微观腐蚀形貌分析，三维表面轮廓分析及电化学分析的研究方法，来表征腐蚀实验现象并进行分析。结果表明：300M超高强钢在中性盐雾环境中的腐蚀产物为FeOOH、Fe2O3、Fe(OH)3和Fe3O4；腐蚀速率随着腐蚀时间逐渐降低，腐蚀后期（72h）腐蚀速率降低50%；腐蚀初期以点蚀为主，点蚀坑通过横向扩展，逐渐发展为后期的均匀腐蚀，腐蚀表面形貌呈沟壑状；外腐蚀层对基体的保护能力很弱，Cr元素在锈层靠近基体的一侧偏聚使内腐蚀层具有一定的抗腐蚀性。     

Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.